The 6-Step Lighting Procurement Checklist I Built After 23 Costly Mistakes
-
Who This Checklist Is For
-
Step 1: Set Lumen Targets Before You Browse Fixtures
-
Step 2: Read the Manufacturer Label, Not Just the Logo
-
Step 3: Choose Your Chandelier Metal Before You Fall in Love With a Photo
-
Step 4: Vet Named Designer Fixtures Like the Aerin Chandelier
-
Step 5: Specify the Control Layer Before You Pick the Fixtures
-
Step 6: Walk the Install Site Before You Place the Order
-
What I'd Add to This Checklist Next Time
Who This Checklist Is For
If you're the person signing off on lighting purchases for a commercial or industrial site—a hotel renovation, a warehouse expansion, a greenhouse build-out, a restaurant refresh—this checklist is for you. I'm not a lighting designer. I'm the guy who approves the PO and then has to live with it.
Over eight years of specifying fixtures and controls, I've personally made and documented 23 significant procurement mistakes, totaling roughly $47,000 in wasted budget. This checklist is what I now keep taped inside our project binder. Six steps. About two hours of work per project. That time has caught about $12,000 in potential errors in the last 18 months alone.
Step 1: Set Lumen Targets Before You Browse Fixtures
The question everyone asks is "which fixture looks best?" The question they should ask is "how many lumens do I actually need out there?" Get the numbers first, then shop.
For outdoor floodlights, the Illuminating Engineering Society (IES) guidance is a useful starting point. Security lighting on a small commercial lot typically runs 700–1,300 lumens. Larger driveways, loading areas, or building facades need 1,300–3,000 lumens. Parking lots and wide industrial yards push past 3,000 lumens, often requiring multiple fixtures rather than one large unit.
That range matters because it changes what you buy. A 1,000-lumen LED floodlight might run $40–$80; a 3,000-lumen commercial unit with a proper housing and mounting bracket is more like $120–$250. If you spec the wrong target, you either waste money on overkill or you pay for a redo.
This pricing roundup was accurate as of Q1 2025. LED pricing moves fast—verify current costs before budgeting.
Step 2: Read the Manufacturer Label, Not Just the Logo
Here's a mistake that sounds stupid until you've made it. "Eaton" shows up on a lot of products. Eaton makes lighting controls, surge protection, power distribution, emergency lighting, and LED fixtures for commercial spaces. Eaton also has a vehicle division that makes things like the transmission temp sensor you'd find on a truck.
I'm not joking—I once spent 40 minutes on a supplier portal trying to cross-reference an "Eaton" part number, only to realize I'd pulled a spec sheet from the wrong business unit. It cost me a phone call and a bruised ego, nothing more. But on a $3,200 order where every single line item needs to match the control panel, that kind of error gets expensive fast.
Most buyers focus on the brand name and completely miss the product family. The question to ask isn't "is this Eaton?" but "which Eaton business unit is this, and does it belong in my lighting spec?"
Step 3: Choose Your Chandelier Metal Before You Fall in Love With a Photo
Brass is having a moment. Brass chandeliers photograph beautifully and signal that someone cared about the room. But brass isn't one thing. Unlacquered brass patinas over time—some clients love it, some file complaints. Lacquered brass holds its color but can chip if it's cheap. And "brass-tone" finishes on budget fixtures are usually painted steel that looks nothing like the real thing under warm light.
I went back and forth between unlacquered and lacquered brass for a lobby project for about two weeks. Unlacquered offered that lived-in richness designers rave about. Lacquered promised consistency for a client who hates surprises. I went with lacquered because the building had a maintenance contract that didn't include polishing—and I've never regretted it.
Decide the finish standard before you pick the fixture. Otherwise you'll fall for a photo of a brass chandelier and then find out it's unavailable in the finish your interior designer already approved.
Step 4: Vet Named Designer Fixtures Like the Aerin Chandelier
Named collections—the Aerin chandelier is a good example—carry real design value and real procurement headaches. They're often made to order, which means lead times of 6–12 weeks. They may come from a single factory, which means if that factory is backordered, you're stuck.
Before committing to a designer fixture, confirm three things in writing: lead time, return policy on opened boxes, and whether the canopy or mounting hardware is included. I once ordered a set of designer pendants and assumed the canopy was included. It wasn't. The canopies added about $85 each on a nine-fixture order. Not catastrophic, but it ate most of the contingency I'd built into that line item.
Here's a tip I've started using: for any fixture line I'm testing for the first time, I order one piece and have it delivered to our shop before the full order goes out. One piece costs more per unit, but it's cheaper than a full-order redo.
Step 5: Specify the Control Layer Before You Pick the Fixtures
This is the step most buyers skip, and it's the one that bites hardest. You can't just buy lights. You have to buy lights that talk to the controls.
If the space requires motion sensors, dimming, or emergency override, the fixture's driver has to be compatible. Eaton's lighting control line, for example, works cleanly with their own contactors and switches—but if you mix in a third-party fixture with an unverified driver, you can end up with flicker, dead zones, or a sensor that won't trigger. Always ask for the driver spec sheet and the control compatibility statement in writing.
What most people don't realize is that "compatible" in a vendor's marketing copy usually means "tested in a lab under ideal conditions." Field conditions add voltage fluctuations, temperature swings, and wiring quirks. Get the compatibility confirmation before the fixtures ship, not after they're installed.
Step 6: Walk the Install Site Before You Place the Order
I learned this one the hard way on a greenhouse project out near Mount Eaton. Every fixture on that job was specified for a standard junction box mounting. Nobody walked the site before the order went out. When the installers got there, half the mounting points were on structural ribs with no standard box. We spent a week and about $1,100 in custom brackets and extra labor fixing something that a 30-minute walk would have caught.
Walk the site with the electrician. Take photos of every mounting location. Check ceiling heights, beam spacing, and where the control panel will actually live. If you can't walk it in person, get the electrician to send photos with a tape measure in frame. This is the step that separates a smooth install from a three-week mess.
What I'd Add to This Checklist Next Time
Quality is a client-perception issue, not just a spec issue. When someone walks into a lobby and sees a cheap-looking brass fixture, that impression attaches to your company—not the fixture brand. The $50-per-fixture difference between mid-tier and premium on a 12-fixture order translates to a noticeably better first impression. I've seen client feedback scores shift after a lighting upgrade, and that's before anyone mentions the lights at all.
The short version, in order:
- Set lumen targets first.
- Confirm the brand and business unit.
- Lock the metal finish standard.
- Vet lead times on named fixtures.
- Verify control compatibility in writing.
- Walk the installation site.
Six steps. Do them in order. Two hours now beats three weeks of fixing later.
The one thing I still get wrong? I sometimes skip Step 6 when I'm in a hurry. I haven't paid for that one again yet—but I will if I'm not careful.